Views: 0 Author: Site Editor Publish Time: 2026-11-20 Origin: Site
If your part must carry structural loads, survive impact, or go through extensive CNC machining, choose 6061-T6. If smooth extrusion, fine surface finish, high-quality anodizing, or complex thin-wall shapes matter most, choose 6063 (T5 or T6). The two alloys are not really competitors — they are designed for different jobs, and most automation projects use both in different places.
Both 6061 and 6063 belong to the 6000 series of aluminum alloys, where magnesium and silicon are the main alloying elements. Both can be precipitation heat-treated (the "T" tempers), weld reasonably well, and resist corrosion far better than steel.
6061 contains more magnesium and silicon, plus small additions of copper and chromium. These additions raise strength and hardness but make the metal slightly harder to push through a complex die.
6063 uses a leaner, carefully balanced silicon–magnesium composition. It flows more easily through extrusion dies, which is why it produces smooth, intricate profiles with an excellent as-extruded surface.
The table below compares the most common tempers — 6061-T6 against 6063-T5 and 6063-T6. Exact values vary with wall thickness and the applicable standard (ASTM B221 in North America; EN 755-9 and EN 12020-2 in Europe).
Property | 6061-T6 | 6063-T5 | 6063-T6 |
|---|---|---|---|
Ultimate tensile strength | ≥260 MPa (typ. 290–310) | ≥160 MPa (typ. ~186) | ≥205 MPa (typ. 205–241) |
Yield strength | ≥240 MPa (typ. 240–276) | ≥110 MPa (typ. ~145) | ≥180 MPa (typ. 160–214) |
Brinell hardness | ~95 HB | 60–75 HB | ~73 HB |
Elongation | 8–12% | 8–12% | 8–12% |
Density | 2.70 g/cm³ | 2.69 g/cm³ | 2.69 g/cm³ |
Extrudability (complex shapes) | Moderate | Excellent | Excellent |
Surface finish / anodizing | Good | Very good | Very good |
CNC machinability | Good | Fair to good | Fair to good |
Relative material cost | Higher (about +10–15%) | Baseline | Slightly above T5 |
6061-T6 is significantly stronger. Its tensile and yield strength run roughly 30–60% above 6063 depending on temper, and it is harder, stiffer under fatigue loading, and more tolerant of impact and vibration. That margin is why 6061 is the default choice wherever a profile acts as a genuine load-bearing structural member.
6063 wins on extrudability and appearance. It flows through the die at higher speeds, supports thin walls down to about 1 mm, and reproduces multi-hollow and fine-detail sections cleanly. It also anodizes more uniformly, producing clear, bronze, or black finishes without streaking — the reason visible architectural parts and consumer-facing components are almost always 6063.
6063 is the most common alloy behind industrial T-slot framing and architectural aluminum. Typical uses include:
T-slot aluminum profiles and modular automation frames (20, 30, 40, 45, 50, 60, 80 and 90 series)
Extruded heat sinks — the thin fins extrude easily, and its thermal conductivity is adequate for most electronics cooling
Window and door frames, curtain walls, thresholds, and decorative trim
Conveyor rails, cable trays, display structures, and furniture
Light-duty machine guards, enclosures, and workstations
For many of these parts, 6063-T5 is the standard temper: it is cooled in air right after extrusion and artificially aged, which keeps cost and lead time down. 6063-T6 adds a solution heat-treatment step for higher strength when the section carries meaningful loads.
Heavy-load machine frames, bases, columns, and structural beams
Brackets, gussets, supports, and fixture plates that see repeated stress
CNC-machined components — its hardness holds tight tolerances and clean cuts better than 6063
Automotive and transport parts, chassis components, and robotic structures
Assemblies requiring good weldability and corrosion resistance
Parts exposed to shock, vibration, or cyclic loading
T5 means the extrusion is quenched (usually in air) at the press and then artificially aged. It is faster and cheaper, with good straightness — the standard for T-slot profiles and non-critical structural sections.
T6 adds a full solution heat treatment followed by artificial aging. The result is notably higher strength and hardness, at extra cost and processing time.
A common practical rule: use 6063-T5 for framing and appearance parts, 6063-T6 for loaded 6063 sections, and 6061-T6 when even 6063-T6 is not strong enough.
Does the part carry calculated structural loads, impact, or high vibration? → 6061-T6
Is the profile visible to the end user or specified with a premium anodized finish? → 6063
Does the section include thin fins, multi-hollow geometry, or walls around 1 mm? → 6063
Will critical dimensions be produced by secondary CNC machining? → lean toward 6061
Is the part a standard T-slot frame, guard, workstation, or heat sink? → 6063-T5
Is budget the deciding factor on a non-safety-critical part? → 6063-T5
Do you need the best balance of strength and weight for a moving or robotic component? → 6061-T6
If the answers are mixed — for example, a loaded frame with visible anodized panels — the standard solution is a mixed-alloy assembly: 6061 for the load-bearing members and 6063 for panels, trim, and guarding.
6061, by a wide margin. In T6 temper, 6061 offers tensile strength of at least 260 MPa and yield strength of at least 240 MPa, compared with roughly 160 MPa and 110 MPa for 6063-T5. Choose 6061 for load-bearing and high-stress parts.
Yes — 6063 is one of the best alloys for anodizing. It accepts clear, bronze, and black anodizing uniformly, with a smooth surface and good color consistency, which is why it is preferred for architectural trim, frames, and visible components.
6063-T5 is the standard choice for extruded heat sinks. It extrudes into thin, closely spaced fins, offers good thermal conductivity for most electronics cooling, and anodizes well when electrical insulation or a black emissive surface is needed. For very high-strength cooling structures, 6061 can be used instead.
Yes. 6061-T6 machines cleanly, holds tight tolerances, and produces good surface finishes, making it the preferred alloy for machined brackets, plates, and precision components. 6063 can be machined, but its softer temper is more prone to burrs and deflection on aggressive cuts.
Most standard T-slot framing is 6063-T5, because it is dimensionally stable, anodizes well, and keeps cost down for typical framing loads. Specify 6061-T6 only when frame calculations show loads, spans, or vibration levels beyond the 6063 design range.
Specifying the right alloy only pays off if your supplier can hold the standard and finish the part correctly. At Shanghai Jinlv Aluminum Alloy Product Co., Ltd. (JINLV), we extrude and stock both 6063-T5/T6 and 6061-T6, including standard T-slot profiles and custom open-die sections, with in-house CNC machining, anodizing, powder coating, sandblasting, and frame assembly under one roof. Profiles can be supplied against ASTM B221 or EN 755 requirements, with material certificates and inspection reports on request.
Send your drawing and load requirements to sales@al-jin.com or contact us via WhatsApp, and our engineers will confirm the correct alloy, temper, and tolerance class for your application before tooling begins./
